Archive

Archive for the ‘MiniPiio’ Category

Raspberry Pi MiniPIIO MIDI board

June 26th, 2014 No comments

We designed our first Pi MIDI interface way back in 2012 while we were waiting for our first Pi board to arrive.

It’s went through several revisions since then and now looks like this:

RPi_MiniPiio_MIDI_small

RPi_MiniPiio_MIDI_Front_small

The circuit is now completely 5V as per the original MIDI specification but the MIDI IN is 3.3V compatible with the Pi via a voltage divider circuit.

OK that’s the hardware what about the software?

Getting a MIDI 31250 Baud Rate on a Pi is not easy as it should be as 31250 is not a standard Pi baud-rate. But you can trick your Pi into it if you overclock (or rather underclock) the UART clock.

Start a terminal session and type:

[sourcecode]
sudo nano /boot/config.txt
[/sourcecode]

Add these lines to the end of the file

[sourcecode]
# Change UART clock to 2441406 for MIDI 31250 baud rate

init_uart_clock=2441406
init_uart_baud=38400
[/sourcecode]

save and exit.

Once saved reboot your Pi.

Next we need to stop the serial UART being used by Raspbian for the shell console. Check my previous post “MiniPIiio RS232 set-up” on how to do this.

Finally we need to add the following to “cmdline.txt”

[sourcecode]
bcm2708.uart_clock=3000000
[/sourcecode]

After doing all of this we should be ready to connect a MIDI keyboard or synth to our Pi.

 

Check our store on Tindie:

https://www.tindie.com/stores/DTronixs/

Categories: MiniPiio, Raspberry Pi Tags:

Four new Raspberry Pi add-on boards

May 13th, 2014 No comments

Another box of new boards arrived today.

In the box where 4, yes 4 sets of PCB’s.

RPi_PIAC_and_others_small
In the photo, the big PCB at the back is RPi-X PIAC. On the photo front row, on the left is MiniPiio LED Breakout, in the centre is MiniPiio BOP4 and to the right is MiniPiio PWM16

RPi-X PIAC is our latest RPi-X experimenter board. The acronym IAC is commonly used to describe an industrial automation and control system and adding a P in this case makes it a Pi Industrial Automation and Control :-)

PIAC has 4x SPCO Relays rated at 2A, 4x opto-isolated digital inputs, 4x 0-10V Analogue inputs and finally a RS485 communications port. So with the RPi-X PIAC you can learn about industrial control or perhaps use it for your own small industrial project.

MiniPiio LED Breakout uses the popular MAX7219 8-digit (64x LED) LED display driver chip to breakout all 64 LED outputs to 8 rows of pin headers. From these pin headers you can plug in individual LED’s to make whatever LED display layout you want. It’s a shame its not Christmas as we think it would make a great blinky LED Christmas tree :-)

MiniPiio BOP4 or Board of Pots (or should that be “Bored of Pots”) has 4 potentiometers (3x rotary and 1x slider) and connects them to a 4-ch MAX3004 ADC. I think it will a great physical user interface. It’ll probably make a great companion to the LED/Switch MiniPiio SimpleIO we showed off a few months back. Of all the new boards I think this is my favourite :-)

The final new PCB, is MiniPiio PWM16. I think its name gives it away. It’s a hardware based 16-channel PWM add-on board using the popular PCA9685.

As always you’ll find them in our Tindie store in the next few days.

Two new Raspberry Pi add-on boards

April 29th, 2014 No comments

A new batch of PCB’s arrived today.

There were two new Raspberry Pi add-on boards in the box.

The first board is a 2-channel Type-K Thermocouple converter based on the MAX31855 chip.

The second board is RF Transceiver based of HopeRF popular RFM12B module.

I’ll plan to build them up in the next few days and if all goes well I’ll list them in our Tindie store.

RPi_MiniPiio_Thermocouple2_RFM12B_small

 

 

New Board – MiniPiio SimpleIO

April 14th, 2014 No comments

MiniPiio SimpleIO is just that, an add-on board with simple inputs and outputs. It features 8x LED’s and 8x tactile switches. The Pi’s GPIO4/17/18/22/23/24/25/27 are each connected to an LED and switch.

You have 8x signals you can mix and match with whatever combination of LED’s or switches your design needs. So if you need more indicators you could have say 6x LED’s and 2x switch inputs and like wise, if you need more inputs than outputs you could have 5x switch inputs and 3x LED outputs.

RPi_MiniPiio_SimpleIO_top_small

You can find them at our store on Tindie.

Note: LED and Switches sharing the same GPIO so are not designed to used simultaneously.

Raspberry Pi RS485 Module

April 8th, 2014 No comments

The MiniPiio RS485 is a RS485 to TTL 3.3V converter board specifically designed to work with the Raspberry Pi.

It uses 3.3V components and is completely voltage compatible with the Raspberry Pi.

The board connects directly to the Raspberry Pi’s UART Rx and Tx to provide RS485 half-duplex communications.

The board uses the industry standard MAX3485* for signal conversion.

An industry standard 9-Way D Connector (Male) and a 3-W screw provides provides the serial connection to the outside world.

Pin-out (9W D):

Pin-5 = 0V Pin-8 = B (Data +) Pin-9 = A (Data -)

In addition, the GPIO signals can be used to control the MAX3485* DE and !RE as needed.

PIIO and MiniPIIO are modular electronic building block for the Raspberry Pi and may be used with our RPi Expander2.

*or Equivalent IC

You can find them on our Tindie store.


MiniPiio Thermocouple

April 6th, 2014 No comments

MiniPiio Thermocouple is a single channel temperature measurement add-on board using Type-K thermocouples.

The MAX31855 is a sophisticated thermocouple-to-digital converter. It features a built-in 14-bit analog-to-digital converter (ADC) for thermocouple measurement. In addition it also contains a cold-junction sensor for compensation temperature sensing and correction.

The MAX31855 resolves temperatures to 0.25°C. It allows readings as high as +1800°C and as low as -270°C and exhibits thermocouple accuracy of ±2°C for temperatures ranging from -200°C to +700°C for K-type thermocouples.

– Works with any K type thermocouple
– Temperature range = -200°C to +1350°C output
– Resolution 0.25 degree
– Accuracy is ±2°C
– Internal cold junction temperature reading
– SPI bus interface
– Two SPi Chips Selects (!CE0 and !CE1)

You can find it at our Tindie store

RPi_MiniPiio_Thermocouple_small

RPi_and_MiniPiio_Thermocouple_small

New board – MiniPIIO Breakout!

March 21st, 2014 No comments

MiniPIIO Breakout! is our newest add-on board for the Raspberry Pi.

It breaks out (hence its name) all the Pi’s expansion I/O into four neat little groups.

UART is broken out into a 6-Way and 4-way pin header. The 6-Way is FTDI USB Cable compatable.

SPI is broken out into two 6-way headers, each with it’s own SPI chip select.

I2C is borken out into two 4-way headers.

GPIO is broken out into two 10-way headers. GPIO4/17/18/22/23/24/25/27 and 3.3V and 0V.

RPi-_MiniPiio_Breakout!_top_small

You can buy it at our Tindie store here

Piio’s and MiniPiio’s boards are now for sale on Tindie

November 9th, 2013 No comments

Pii and MiniPiio Boards are now for sale on Tindie

Details are here:

https://www.tindie.com/stores/DTronixs/

Categories: MiniPiio, PCB, Raspberry Pi Tags:

MiniPiio Boards now stocked by Elektronik Lavpris Aps

March 27th, 2013 No comments

We are please to announce that our MiniPiio Boards are now stocked by

Elektronik Lavpris Aps of Denmark

You can find them on their website:

http://www.elektronik-lavpris.dk

Categories: MiniPiio Tags:

New MiniPiio SimpleIO and RS485

March 24th, 2013 No comments

We’ve got a couple of new MiniPiio boards in the works.

The first MiniPiio is SimpleIO which is 8x LED’s and 8x Tactile Switches connected to the GPIO signals. This is currently being manufactured, so we’ll let you know how it goes.

RPi_MiniPiio_SimpleIO_0v10
RPi_MiniPiio_SimpleIO_0v10

The second MiniPiio is a serial RS485 board. It’s the one I’ve been asked a lot for. The layout is finished and its going out for manufacture next week.

RPi_MiniPiio_RS485 0v10
RPi_MiniPiio_Rs485 0v10

Categories: MiniPiio, PCB, Prototype, Raspberry Pi Tags: